Mobile phone Type-C charging cable also has correct usage specifications

A netizen recently sent him a "tragic" on the Internet. For the sake of convenience, it has been using VIVO's original charging cable and charging head to charge all Type-C charging ports. This has been used for a year or two. What is the problem. I know that this netizen has recently started a full-format Bluetooth decoding HiFi music player. Because it is also a Type-C interface, this netizen has also charged the music player according to the "international convention". Have fun. After about an hour, the netizen estimated that it was already fully charged, and he was ready to unplug the charging line, but it was a problem at this time.
Type-C cable
When the netizen's mobile phone touched the music player, the instant condition reflexed the finger back. The music player was hot and hot at this time. After the user unplugged the charger, he tried it again with his finger and found the music. The temperature of the player is about seventy degrees, just like it is going to blow up. After ten minutes, he pulled the charging cable off the player. When he checked, he found that the charging port had burned out, and the plastic on the back side melted. You can see that there are still a lot of dip in the music player's socket. Residue after burning on top.
Fortunately, this netizen has not left the charging room, or else he still has a fire! The netizen used by this netizen is 9V/2A and 5V/2A adaptive. It is reasonable to say that it should be no problem, but it may be a BUG in the charging chip, resulting in abnormal current. Konnra Electronics warns everyone that it is better not to mix the same type of equipment, because the charging chip and charging protocol of each device are different. If it is used indiscriminately, it may cause similar fire or even explosion time.



评论

发表评论

此博客中的热门博文

What is the coaxial connector?

图片
Coaxial connectors are used to transmit RF signals. They have a wide transmission frequency of up to 18 GHz or higher and are mainly used for radar, communication, data transmission and aerospace equipment. The basic structure of the coaxial connector includes: a center conductor (a positive or negative center contact); a dielectric material outside the inner conductor, or an insulator, and the outermost is an outer contact, which serves as a shield outside the coaxial cable. The same function of the layer, that is, the signal transmission, the grounding element as a shield or circuit. The coaxial connectors are mainly divided into: SMA, SMB, BNC, TNC, SMC, N-type, BMA, and the like. Male: Male (plug), thread inside, inside is the needle. Such as TNC (M). Female: Female (socket), threaded outside, inside is a hole. Such as SMA (F). RP: Reverse Polarity means that the head and the inside of the needle are opposite. Bulkhead: It is the joint of the lockable screw on the board and
阅读全文

Talking about the function, classification and working principle of OTG data line

图片
  What is the OTG line? OTG is mainly applied to the connection between various devices or mobile devices for data exchange. The development of USB technology enables computers and peripheral mobile devices to transmit various data through simple USB connections. This will lead to a situation, once the mobile phone or tablet does not have a computer, we cannot manage the data of mobile devices such as mobile phones, which brings inconvenience to users. As mobile devices such as mobile phones become more and more like computers, can we imagine that we can use mobile phones as computers? Can a U disk, USB network card, etc. be connected to the phone? The answer is yes, the OTG function is to realize that the mobile phone can be connected with USB devices such as U disk, but the mobile phone has a tiny   USB   interface, which cannot meet the needs of USB ports such as U disk. So far, the OTG data cable came into being. The role of OTG is to realize data transfer between mobile devices wi
阅读全文

Calculation method of wire diameter of automobile wiring harness

图片
  When using the CATIA module for wire harness data production, the wire harness segment diameter is written into the software as an important parameter. All subsequent clearance checks and motion analysis are based on this value. Therefore, if there is a big difference from the actual situation, it will inevitably lead to the original requirement of meeting the safety gap, and it will be found to have interfered when the vehicle is actually installed, or even cannot be assembled. Konnra wiring harness  engineers provide you with a theoretical calculation method (wire harness standard algorithm) for estimating the outer diameter of automotive wiring harnesses. A wire harness segment is a collection that binds all wires together with tape or other wrapping. Taking into account that the tape is only wound on the wire harness, and the wrapping of casings such as corrugated pipes also needs to determine the outer diameter of the wire harness before selection. Therefore, when calculating, w
阅读全文