Terminal cable Inspection and packaging process of finished products

In the previous issue, Konnra Electronics engineers explained the terminal wire processing production process. In this issue, Konnra Electronics is going to introduce the inspection and packaging process of the terminal wire finished products, and hope to pass the terminal wire packaging process. The explanation, you can have a deeper understanding of the inspection of the finished terminal wire.
Konnra Electronics connector engineer pointed out that the inspection and packaging process of the terminal wire finished product mainly includes five steps of electrical inspection of terminal wire, appearance inspection of terminal wire, terminal wire assembly, terminal wire assembly and terminal wire packaging. 
FRC cable_Konnra Electronics
1. Terminal cable electrical detection
The finished product of the crimped terminal wire is tested by a standard wire testing machine for the withstand voltage, impedance, short circuit, etc. of the terminal wire, and after checking, the flow goes to the next inspection process.
2. Terminal cable appearance inspection
Check the terminal wire of the electrical test OK with a light magnifying glass to check whether there is any defect, or use the naked eye to check whether some appearance parts meet the standard, whether there is a missing attachment, etc. Check the OK and flow to the next terminal cable packaging process.
3. Terminal cable dispensing
The finished terminal wire of the OK check is dispensed according to the packaging process requirements, that is, the terminal part of the terminal wire is inserted into the sheath to complete the dispensing process of the terminal wire.
4. Terminal cable assembly
The completed finished product is assembled according to the circuit pattern on the terminal cable specification process board, which is bundled with tape or a strap to complete the assembly process of the terminal cable.
5. Terminal cable packaging
The assembled terminal wires are neatly arranged and packaged according to the terminal wire specification process diagram, such as: 500PCS/carton, 50PCS/zab, 5 bar/bag, 2 bags/carton, etc.; when the terminal wire is filled in the box, the seal is used. The box machine seals the box mouth and attaches the product label of the harness terminal cable. After completing the above five inspection packaging process, the terminal cable products can be shipped.
Konnra Electronics


评论

发表评论

此博客中的热门博文

What is the coaxial connector?

图片
Coaxial connectors are used to transmit RF signals. They have a wide transmission frequency of up to 18 GHz or higher and are mainly used for radar, communication, data transmission and aerospace equipment. The basic structure of the coaxial connector includes: a center conductor (a positive or negative center contact); a dielectric material outside the inner conductor, or an insulator, and the outermost is an outer contact, which serves as a shield outside the coaxial cable. The same function of the layer, that is, the signal transmission, the grounding element as a shield or circuit. The coaxial connectors are mainly divided into: SMA, SMB, BNC, TNC, SMC, N-type, BMA, and the like. Male: Male (plug), thread inside, inside is the needle. Such as TNC (M). Female: Female (socket), threaded outside, inside is a hole. Such as SMA (F). RP: Reverse Polarity means that the head and the inside of the needle are opposite. Bulkhead: It is the joint of the lockable screw on the board and
阅读全文

Talking about the function, classification and working principle of OTG data line

图片
  What is the OTG line? OTG is mainly applied to the connection between various devices or mobile devices for data exchange. The development of USB technology enables computers and peripheral mobile devices to transmit various data through simple USB connections. This will lead to a situation, once the mobile phone or tablet does not have a computer, we cannot manage the data of mobile devices such as mobile phones, which brings inconvenience to users. As mobile devices such as mobile phones become more and more like computers, can we imagine that we can use mobile phones as computers? Can a U disk, USB network card, etc. be connected to the phone? The answer is yes, the OTG function is to realize that the mobile phone can be connected with USB devices such as U disk, but the mobile phone has a tiny   USB   interface, which cannot meet the needs of USB ports such as U disk. So far, the OTG data cable came into being. The role of OTG is to realize data transfer between mobile devices wi
阅读全文

Calculation method of wire diameter of automobile wiring harness

图片
  When using the CATIA module for wire harness data production, the wire harness segment diameter is written into the software as an important parameter. All subsequent clearance checks and motion analysis are based on this value. Therefore, if there is a big difference from the actual situation, it will inevitably lead to the original requirement of meeting the safety gap, and it will be found to have interfered when the vehicle is actually installed, or even cannot be assembled. Konnra wiring harness  engineers provide you with a theoretical calculation method (wire harness standard algorithm) for estimating the outer diameter of automotive wiring harnesses. A wire harness segment is a collection that binds all wires together with tape or other wrapping. Taking into account that the tape is only wound on the wire harness, and the wrapping of casings such as corrugated pipes also needs to determine the outer diameter of the wire harness before selection. Therefore, when calculating, w
阅读全文