KR1507 inner buckle connector

Konnra Electronics introduces its new KR1507 connector，which are designed for applications that require higher pin count connectors to carry more signal lines in less space; the system includes a unique tuning-fork terminal concept that provides low-insertion force and secure mating contact.
KR1507 connectrs have two types:DIP and SMT,each type have 90° and 180°.
KR1507 inner buckle connector
【1】This specification covers the KR1507 1.5 Pitch Bar Connectors series.

【2】PRODUCT NAME AND PART NUMBER
 Product Name
Part Number
MX1.5 inner buckle
KR1507 connector

【3】RATINGS
 Item
Requirement
Rated Voltage(MAX)
100V
[AC(virtual value)/DC]
Rated Current(MAX)
2A
Ambient temperature Range
-40℃ ～ +85℃

【4】PERFORMANCE
4.1 Electrical Performance
Item
Test Condition
Requirement
4.1.1
Contact Resistance
Mate connectors, measure by dry circuit, 20mV
MAX, 10mA.
(Based upon EIA-364-06A).
Initial:20 milliohms Max.
After Test:40 milliohms Max
4.1.2
Insulation Resistance
Mate connectors, apply 250V DC between
adjacent terminal or ground.
(Based upon EIA-364-21B / MIL-STD-202
Method 302 Cond.B)
500 Megohms Min.
4.1.3
Dielectric
Mate connectors, apply 500V AC for 1 minute
between adjacent terminal or ground.
(Based upon EIA-364-20A / MIL-STD-202
Method 301)
No Breakdown
and Flashover
4.1.4
Contact
resistance on
crimped
portion
Crimp the applicable wire on to the terminal
measure by dry circuit 20mV MAX, 10mA.
10 milliohms Max.

4.2  Mechanical Performance
Item
Test Condition
Requirement
4.2.1
Insertion and Withdrawal Force
Insert and withdraw connectors at the speed rate of 25.4±3mm/minute.
Refer to paragraph 7
4.2.2
Terminal/
Housing
Retention
Force
Apply axial pull out force at the speed rate of
25.4±3mm/minute on the terminal
assembled in the housing.
9.8N {1.0kgf} Min.
4.2.3
Terminal
Insertion
Force
Insert the crimped terminal into the
housing.
9.8N {1.0kgf} Max.
4.2.4
Pin
Retention Force
Apply axial push force at the speed rate
of 25.4±3mm/minute.
2.94N {0.3kgf} min.
4.2.5
Tensile strength
(Crimped
connections)
Fix the crimped terminal, apply axial pull out
force on the wire. (Do not crimp insulation part).
AWG#
#24#26#28
Spec.kgf.
Min.
3.02.01.0


4.3 Environmental Performance and Others
ItemTest ConditionRequirement
4.3.1
Repeated Insertion and Withdrawal
When mated up to 50 cycles repeatedly
by the rate of 10 cycles per minute.
Contact Resistance
40 mΩ
MAX
4.3.2
Temperature Rise
Carrying rated current load. (UL 1977)
Temperature Rise
30 ℃  MAX
4.3.3
Vibration
Amplitude: 1.5mm P-P
Sweep time: 10~55~10 HZ in 1 minute
Duration: 2 hours in each X.Y.Z axials.
(Based upon EIA-364-28B/MIL-STD-202
Method 213B Cond.A)
Appearance
No Damage
Contact Resistance
40 mΩMAX
Discontinuity
1 ms MAX.
4.3.4
Shock
strokes in each X.Y.Z. axes.
(Based upon EIA-364-27B/MIL-STD-202
Method 213B Cond.A)
Appearance
No Damage
Contact Resistance
40 milliohms
Max.
Discontinuity
1microsecond Max.
4.3.5
Humidity
Temperature: 40±2℃
Relative Humidity: 90~95%
Duration: 96 hours
(Based upon EIA-364-31A/MIL-STD-202
Method 103B Cond.B)
Appearance
No Damage
Contact Resistance
40 mΩMAX
Discontinuity
Must meet 4.1.3
Insulation Resistance
100 MΩ MIN
4.3.6
Heat Resistance
85±2℃,96 hours.
(Based upon MIL-STD-202 Method 108A
Cond.A)
AppearanceNo Damage
Contact Resistance40 mΩMAX
4.3.7
Cold Resistance
-25±5℃,96 hours.
( Based upon EIA-364-105)
AppearanceNo Damage
Contact Resistance
40 milliohms Max.
4.3.8Temperature
Cycling
5 cycles of: a) -55℃ 30 minutes.b) +85℃ 30 minutes.
(Based upon EIA-364-32B)
AppearanceNo Damage
Contact Resistance40 milliohms Max.
4.3.9
Salt Spray
24±1 hours exposure to a salt spray from the 5±1% solution at 35±2℃.
(Based upon EIA-364-26A/MIL-STD-202Method 101D Cond.B).
AppearanceNo Damage
Contact Resistance40 milliohms Max.
4.3.10Solderability
Soldering Time: 5±0.5second.
Solder Temperature: 245±5℃.
(Based upon EIA-364-52)
Solder Wetting
95% of
immersed area
must show no
voids, pin
holes.
4.3.11
Solder-
Resistance
Soldering time:5~10 sec solder.
Temperature:260+5/-5℃.
(Based upon EIA-364-56A)
Appearance
No Damage

【5】 PEAK TEMPERATURE PROFILE 
PEAK TEMPERATURE PROFILE
【6】PRODUCT SHAPE,DIMENSIONS AND MATERIALS
REFER TO THE DRAWING
NAME
MATERIALS
Housing
PBT UL94V-0 or UL94 V-2
Terminal
Phosphor Bronze
Wafer
PA9T UL94 V-0 or UL94 V-2&Brass
Remark


【7】INSERTION/WITHDRAWAL FORCE
No. of CKTFirst Insertion (kgf Max.)30th Withdrawal (kgf Min.)No. of CKTFirst Insertion (kgf Max.)30th Withdrawal (kgf Min.)
020.660.04092.970.18
030.990.06103.300.20
041.320.08113.630.22
051.650.10123.960.24
061.980.12134.290.26
072.310.14144.620.28
082.640.16154.950.30





评论

发表评论

此博客中的热门博文

What is the coaxial connector?

图片
Coaxial connectors are used to transmit RF signals. They have a wide transmission frequency of up to 18 GHz or higher and are mainly used for radar, communication, data transmission and aerospace equipment. The basic structure of the coaxial connector includes: a center conductor (a positive or negative center contact); a dielectric material outside the inner conductor, or an insulator, and the outermost is an outer contact, which serves as a shield outside the coaxial cable. The same function of the layer, that is, the signal transmission, the grounding element as a shield or circuit. The coaxial connectors are mainly divided into: SMA, SMB, BNC, TNC, SMC, N-type, BMA, and the like. Male: Male (plug), thread inside, inside is the needle. Such as TNC (M). Female: Female (socket), threaded outside, inside is a hole. Such as SMA (F). RP: Reverse Polarity means that the head and the inside of the needle are opposite. Bulkhead: It is the joint of the lockable screw on the board and...
阅读全文

The optical fiber connector

图片
A fiber optic connector is a detachable (active) connection between an optical fiber and an optical fiber. The two end faces of the optical fiber are precisely butted together so that the optical energy output from the transmitting optical fiber can be coupled to the receiving optical fiber to the maximum extent. It also minimizes the impact on the system due to its involvement in the optical link, which is a basic requirement for fiber optic connectors. To some extent, fiber optic connectors affect the reliability and performance of optical transmission systems. Basic introduction A connecting device for re-plugging between optical fibers, also called a fiber optic movable joint. The main performance parameters (and typical values) are: insertion loss (<0.5dB), plug-and-repeat repeatability and interchangeability between connectors (500 changes). When used in a large-capacity high-speed transmission system, reflection is also required to be small. Introduction Optical fiber con...
阅读全文

The working principle of IDC termination method

图片
Introduction and background IDC termination method is often used in various applications. This termination technology has been successfully applied to a variety of industries where multi-contact mass termination and very economical. Multi-point cable termination can be achieved with insulation displacement  connectors (IDC)  because the termination force is relatively small (usually a few pounds, while crimping is hundreds of pounds). In addition, another advantage of this technology is that it eliminates the stripping operations required in crimping. Therefore, in many electronic applications, such large-scale terminations are often used when using multi-strand cables. In many cases, multiple flat cables are used for this very economical large-scale termination. However, discrete multi-strand cables can also be used to reduce costs because the steps of cable stripping preparation and terminal insertion are eliminated. This type of application provides rapid assembly of high-d...
阅读全文