USB 3.2 standard can be used on PC during the year

According to the latest USB naming convention published by USB-IF, the original USB 3.0 and USB 3.1 will no longer be named. All USB standards will be called USB 3.2. Of course, considering compatibility, USB 3.0 to USB 3.2 are called respectively. USB 3.2 Gen 1, USB 3.2 Gen 2, USB 3.2 Gen 2x2.
USB 3.2
For the new USB 3.2 Gen 2x2 naming, it uses all the data pins up and down to double the data speed. So, when will the USB 3.2 Gen 2x2 device be used?
The USB-IF standards group revealed that the USB 3.2 Gen 2x2 controller will be available later in 2019, meaning that consumers will be able to use the latest standards in their desktops during the year. In other words, consumers can use existing devices by purchasing peripherals that support the USB 3.2 Gen 2x2 standard.
usb 3.2 specification
For the USB socket and the standard big name, including USB 3.0 and USB 3.1, after the unified system, everyone is called USB 3.1. For example, in July 2013, after USB 3.1 was released, USB-IF called all USB 3.X USB 3.1, including USB 3.1 Gen 1 and USB 3.1 Gen 2. Now that USB 3.2 has been released for a while, USB-IF has to do something new, and that is the reunification of the USB 3.X series.
The news is organized by Konnra Electronics.



评论

发表评论

此博客中的热门博文

What is the coaxial connector?

图片
Coaxial connectors are used to transmit RF signals. They have a wide transmission frequency of up to 18 GHz or higher and are mainly used for radar, communication, data transmission and aerospace equipment. The basic structure of the coaxial connector includes: a center conductor (a positive or negative center contact); a dielectric material outside the inner conductor, or an insulator, and the outermost is an outer contact, which serves as a shield outside the coaxial cable. The same function of the layer, that is, the signal transmission, the grounding element as a shield or circuit. The coaxial connectors are mainly divided into: SMA, SMB, BNC, TNC, SMC, N-type, BMA, and the like. Male: Male (plug), thread inside, inside is the needle. Such as TNC (M). Female: Female (socket), threaded outside, inside is a hole. Such as SMA (F). RP: Reverse Polarity means that the head and the inside of the needle are opposite. Bulkhead: It is the joint of the lockable screw on the board and
阅读全文

Talking about the function, classification and working principle of OTG data line

图片
  What is the OTG line? OTG is mainly applied to the connection between various devices or mobile devices for data exchange. The development of USB technology enables computers and peripheral mobile devices to transmit various data through simple USB connections. This will lead to a situation, once the mobile phone or tablet does not have a computer, we cannot manage the data of mobile devices such as mobile phones, which brings inconvenience to users. As mobile devices such as mobile phones become more and more like computers, can we imagine that we can use mobile phones as computers? Can a U disk, USB network card, etc. be connected to the phone? The answer is yes, the OTG function is to realize that the mobile phone can be connected with USB devices such as U disk, but the mobile phone has a tiny   USB   interface, which cannot meet the needs of USB ports such as U disk. So far, the OTG data cable came into being. The role of OTG is to realize data transfer between mobile devices wi
阅读全文

Calculation method of wire diameter of automobile wiring harness

图片
  When using the CATIA module for wire harness data production, the wire harness segment diameter is written into the software as an important parameter. All subsequent clearance checks and motion analysis are based on this value. Therefore, if there is a big difference from the actual situation, it will inevitably lead to the original requirement of meeting the safety gap, and it will be found to have interfered when the vehicle is actually installed, or even cannot be assembled. Konnra wiring harness  engineers provide you with a theoretical calculation method (wire harness standard algorithm) for estimating the outer diameter of automotive wiring harnesses. A wire harness segment is a collection that binds all wires together with tape or other wrapping. Taking into account that the tape is only wound on the wire harness, and the wrapping of casings such as corrugated pipes also needs to determine the outer diameter of the wire harness before selection. Therefore, when calculating, w
阅读全文