Board to board connector connection problems and troubleshooting methods

After reading this article, users will clearly know how to connect board to board connectors and how to deal with board to board connector products after a failure. I hope that users will be able to apply the knowledge of these board to board products to the actual situation. In this operation, this did not disappoint the finishing of the engineer of Konnra connector.
Correctly connecting the board to board connector products can increase the service life of the product and ensure the good operation of mechanical equipment. Board to board products have failed, and immeasurable economic losses have not been made in a timely manner. The following is an electrical engineer to introduce the board to board connector circuit connection and troubleshooting methods.
Pin header
I. About the connection problem of board to board connector
The board to board plug and socket are used to electrically connect two circuit boards separated from each other. The board to board plug and socket include a first connector that is connected to the circuit board and a transfer connector that is used to serially connect the first connector. The first terminal that is connected and the body that houses the first terminal. The transfer connector is provided with a second terminal and a body accommodating the second terminal, and the second connection terminal end can be mated and mated with the first connection terminal to achieve the first connector respectively provided on the two circuit boards. One of the first terminal and the second terminal is an elastic portion bent in the opposite direction, and the main body and the second terminal can select a suitable extension length according to the distance setting standard of the circuit board.
Pin header
II.Troubleshooting of board to board connector
Once the product fails, it can be judged that the cause is a broken wire during use, and the product is loose. The frequency of the broken wire in the middle is not much. Most of the inspection at the connector is to focus on the sensor and the connecting wire, to see if they have problems such as loosening and poor contact. Generally, open circuit faults caused by poor contact are mostly rusted, and external dirt enters the terminals or connection sockets, which causes the contact pressure to decrease. To cope with such a failure, it is necessary to remove the connector, then plug it in again, change it, and return it to normal contact.

评论

发表评论

此博客中的热门博文

What is the coaxial connector?

图片
Coaxial connectors are used to transmit RF signals. They have a wide transmission frequency of up to 18 GHz or higher and are mainly used for radar, communication, data transmission and aerospace equipment. The basic structure of the coaxial connector includes: a center conductor (a positive or negative center contact); a dielectric material outside the inner conductor, or an insulator, and the outermost is an outer contact, which serves as a shield outside the coaxial cable. The same function of the layer, that is, the signal transmission, the grounding element as a shield or circuit. The coaxial connectors are mainly divided into: SMA, SMB, BNC, TNC, SMC, N-type, BMA, and the like. Male: Male (plug), thread inside, inside is the needle. Such as TNC (M). Female: Female (socket), threaded outside, inside is a hole. Such as SMA (F). RP: Reverse Polarity means that the head and the inside of the needle are opposite. Bulkhead: It is the joint of the lockable screw on the board and...
阅读全文

Talking about the function, classification and working principle of OTG data line

图片
  What is the OTG line? OTG is mainly applied to the connection between various devices or mobile devices for data exchange. The development of USB technology enables computers and peripheral mobile devices to transmit various data through simple USB connections. This will lead to a situation, once the mobile phone or tablet does not have a computer, we cannot manage the data of mobile devices such as mobile phones, which brings inconvenience to users. As mobile devices such as mobile phones become more and more like computers, can we imagine that we can use mobile phones as computers? Can a U disk, USB network card, etc. be connected to the phone? The answer is yes, the OTG function is to realize that the mobile phone can be connected with USB devices such as U disk, but the mobile phone has a tiny   USB   interface, which cannot meet the needs of USB ports such as U disk. So far, the OTG data cable came into being. The role of OTG is to realize data transfer between mob...
阅读全文

BNC interface protocol in video output

图片
In the following, you will be presented with a set of questions and answers about the "What protocol is going on in the BNC interface video output" and the  Konnra Electronics  engineers' Q&A record, so that you can easily understand what protocol is going on in the video output of the BNC interface in the interaction. related question. The core of the problem: What protocol is going inside the BNC interface video output? Problem Description: For example, this bnc interface video output device, BNC is the signal of the H.264 protocol, it is necessary to configure the photoelectric conversion equipment between it and the camera, how to configure it? What kind of docking can it be? Answer: The BNC interface input and output is commonly referred to as the Q9 header, which is used to transmit baseband video signals. The single BNC port of the monitoring device transmits the analog composite signal. The video recorder saves the video file of the analog video signal into...
阅读全文